Service Hotline:86-13928286213

0086-0757-29212632 / 29212631

全自動貼標機廠家

categories of news

contact us

Foshan ToKen Impression Machinery Co., Ltd.

Mobilephone: 86-13928286213

Tel: 0086-0757-29212632 / 29212631

Fax: 0086-0757-23276178 / 23276177

Email: labelfs@163.com

Website: www.angelcityjazzfestival.com

Address: No.4, Street 1, Fengnan Road, Ronglili, Ronggui County, Shunde District, Foshan City

>>Back to home

Your current location: Home >> News >> Industry news

General automatic labeling machine common faults and maintenance methods

Release date:2018-11-28 Author: Click:

The use of automatic labeling machine will inevitably lead to some failures. Today, automatic labeling machine manufacturers list the problems that often occur in automatic labeling machines, hoping to help everyone:

Adjustment of the brushing device:

The center of the brush is aligned and the two sides are symmetrical. The brush is perpendicular to the surface of the container. The overlapping gap of the brushing sweeping container is: a single pressing brush is 10 mm to 15 mm, and the combined pressing brush is 5 mm to 10 mm. The position of the cleaning brush from the sponge is 1 mm to 2 mm. Adjustment of the bottle head. The bottle head should be 20mm lower than the bottle when there is no bottle

Label box adjustment:

The center line of the standard box, the center axis of the standard station is tangent to the label paper, and the center axis of the target board is lined up at three points. The adjustment target board is tangent to the label paper (0 distance), and then the standard box is moved closer to 1 mm to 2 mm. The gap between the standard paper and the bead on both sides should be between 0.8mm-1mm. The gap is too large, causing the standard paper to shift in the standard box, and the skew mark appears. If the gap is too small, the push mark will be poor. The adjustment of the position of the labeling hook of the standard box: the upper and lower and the left and right grasping hooks are on the same vertical plane and evenly work on the standard paper, so that the label can be smoothly captured. Adjustment of the label supply roller: When there is no label, the label platen can be pressed to the front end of the label box and the label near the label hook finger cannot be crushed.

Adjustment of the bottle star wheel, the bottle star wheel, and the bottle screw:

When adjusting the inlet and outlet star wheels and the feeding screw, the pressure head of the labeling machine shall prevail. First adjust the bottle into the star wheel. When the bottle head just overwhelm the bottle, adjust the bottle into the star wheel so that the bottle is in the middle of the star wheel groove. Adjustment of the inlet screw: According to the inlet star wheel, when the bottle is in the middle of the groove of the inlet star wheel, adjust the auger so that the auger is pressed against the bottle side without displacement. Adjustment of the bottle star wheel: When the bottle head has just been lifted, adjust the star wheel so that the bottle is in the middle of the groove of the star wheel.

Adjustment of the standard station:

Adjustment of the squeegee and the rubber roller: The squeegee and the rubber roller should not have a gap over the entire length. If there is a gap, the squeegee can be adjusted by adjusting the eccentric bolt. Adjustment of the rubber roller and the target plate: the target plate and the rubber roller only contact each other without any pressure. If the gap is too large, the glue on the label will be too much, causing the glue. The gap is too small, the contact is too tight, the glue will be squeezed away, and there is no glue on the half of the target. Practice has proved that the gap between the target plate and the rubber roller is preferably between 0.1 mm and 0.2 mm. This can be achieved by adjusting the bearing housing in the lower part of the rubber roller and adjusting the bearing on the upper part of the rubber roller if necessary.


This article URL:http://www.angelcityjazzfestival.com/en/news/376.html

Related tags:全自動貼標機廠家

  • service
  • contact
    13928286213
  • message
  • Online consultation